Pit Maneuver Survivor

Tell us about your new PPV, show us some pictures, let us know how you did what you did!
Forum rules
One thread per car per member in this section. No thread hijacking in this section please, if it's strictly a tech discussion please move it to the appropriate sub-forum - moderators can assist if needed or requested.
User avatar
rustingsoftly
Posts: 19
Joined: Sun Jan 07, 2024 11:50 pm

Pit Maneuver Survivor

Post by rustingsoftly »

2014 Caprice PPV

40,xxx miles
Engine 105,xxx miles + refresh by me!
City of Centralia, WA Police Car #2

Learned this cars full backstory after purchasing it and learning where it had come from. Called the city shop and asked about its history.

Here’s the low down:
My car pit maneuvered a lifted duramax in late 2020. Front clip was replaced with a good 2012 parts car by the city with the intentions of making a training car. Ultimately another PPV in their fleet needed a good engine and they swapped it with this 40,000 mile one from this car and put the bad cam lobe/lifter failure engine in and sent it to auction. Luckily it still has its original 40k tranny.

Goals: reliable cruiser. Similar to stock mpg. 87 octane/flex.
IMG_9007.jpeg
IMG_9007.jpeg (3.58 MiB) Viewed 691 times
Decided that if I fix it and I will eventually get my moneys worth out of it. Plus I’ll get to enjoy a cool car. win-win.

So I got it home and drove it. Learned it had bad misfire at idle on cylinder 3. While driving around the misfire went away. Checked the coils and felt confident that their diagnosis was accurate.
IMG_9053.jpeg
IMG_9053.jpeg (1.24 MiB) Viewed 691 times
IMG_9100.jpeg
IMG_9100.jpeg (2.08 MiB) Viewed 691 times
IMG_9102.jpeg
IMG_9102.jpeg (1.47 MiB) Viewed 691 times
IMG_9132.jpeg
IMG_9132.jpeg (3.73 MiB) Viewed 691 times
Pulled cylinder head and found lobes/lifters for #3 were bad and #4 was also on the way out
Last edited by rustingsoftly on Thu Feb 01, 2024 12:35 am, edited 3 times in total.
User avatar
rustingsoftly
Posts: 19
Joined: Sun Jan 07, 2024 11:50 pm

Re: Pit Maneuver Survivor

Post by rustingsoftly »

Original plan was to just replace the cam, lifters, and associated parts. When I initially pulled the camshaft it acted stuck. I had all the lifters out but something was in a bind. I pulled really hard and it came way out and got stuck again 🤬. Finally got it to go but the cam was covered in scratches from the cam bearings trying to hold the cam from coming out.
IMG_9275.jpeg
IMG_9275.jpeg (1.48 MiB) Viewed 690 times
No buenno.

Well so much for the slam and jam with the new camshaft. It would just ruin it trying to put it in. So I guess it was time to learn about cam bearings.

I decided that it would be much easier to replace the cam bearings by pulling the crankshaft out.

Well that spiraled into finding more junk embedded in the main bearings and a little in a few connecting rod bearings.
IMG_9245.jpeg
IMG_9245.jpeg (2.8 MiB) Viewed 690 times
IMG_9246.jpeg
IMG_9246.jpeg (2.51 MiB) Viewed 690 times
IMG_9255.jpeg
IMG_9255.jpeg (1.77 MiB) Viewed 690 times
The crankshaft journals seemed pretty good so I had it mic’d and polished locally.

I ordered fresh Clevites for the bottom end and some Durabonds for the cam bearings. (I’m not against trying all the brands to see what’s good).
Shiny ✨
Shiny ✨
IMG_9314.jpeg (2.47 MiB) Viewed 690 times
IMG_9283.jpeg
IMG_9283.jpeg (2.41 MiB) Viewed 690 times
Last edited by rustingsoftly on Thu Feb 01, 2024 12:51 am, edited 2 times in total.
User avatar
rustingsoftly
Posts: 19
Joined: Sun Jan 07, 2024 11:50 pm

Re: Pit Maneuver Survivor

Post by rustingsoftly »

Decided to try painting an LS for the first time. Turned out pretty good!
IMG_9292.jpeg
IMG_9292.jpeg (2.5 MiB) Viewed 690 times
Plasti-gauged the bearings and had consistent 0.002” for all them which was very reassuring.
IMG_9326.jpeg
IMG_9326.jpeg (2.04 MiB) Viewed 690 times
IMG_9327.jpeg
IMG_9327.jpeg (2.18 MiB) Viewed 690 times
IMG_9328.jpeg
IMG_9328.jpeg (2.7 MiB) Viewed 690 times
Reused the main cap bolts because sloppy mechanics has proven it’s fine. You can torque them 3 times so it’s mint.

[attachment=1]IMG_9343.jpeg[/attach
Slammed some new cam bearings in it for the first time ever.
Attachments
IMG_9343.jpeg
IMG_9343.jpeg (1.5 MiB) Viewed 690 times
Last edited by rustingsoftly on Thu Feb 01, 2024 12:31 am, edited 1 time in total.
User avatar
rustingsoftly
Posts: 19
Joined: Sun Jan 07, 2024 11:50 pm

Re: Pit Maneuver Survivor

Post by rustingsoftly »

Torqued the inner-mains, set the thrust, final pass on the inside, then I jumped outside and did my first and final passes. Bada bing. Checked my crank end play and we had 0.0035”

Mint
IMG_9341.jpeg
IMG_9341.jpeg (3.23 MiB) Viewed 689 times
IMG_9339.jpeg
IMG_9339.jpeg (2.24 MiB) Viewed 689 times
Tomorrow will clean up some pistons and start that process.
User avatar
rustingsoftly
Posts: 19
Joined: Sun Jan 07, 2024 11:50 pm

Re: Pit Maneuver Survivor

Post by rustingsoftly »

IMG_9372.jpeg
IMG_9372.jpeg (2.8 MiB) Viewed 481 times
Pistons in! This part is always time consuming. Cleaned up the rings. Left a little stubborn carbon on top of the pistons for extra compression.
IMG_9398.jpeg
IMG_9398.jpeg (3.62 MiB) Viewed 481 times
Bopped these a37 bearing pieces in with a little cherry flavor loctite.
IMG_9399.jpeg
IMG_9399.jpeg (2.96 MiB) Viewed 481 times
Slammed the cam in
Installed new timing gear and ls2 chain
Shimmed the oil pump and torqued it down.

I have had good luck with the stock 2500hd truck pump. I had like hot 35-40 psi and 80+ psi oil pressure at 7,000 rpm in my turbo truck so it’s gonna work good.

Put the new springs on the heads today.
User avatar
rustingsoftly
Posts: 19
Joined: Sun Jan 07, 2024 11:50 pm

Re: Pit Maneuver Survivor

Post by rustingsoftly »

IMG_9447.jpeg
IMG_9447.jpeg (3.7 MiB) Viewed 369 times
Oil pan and rear cover put on. Upgraded to a Sac City Corvette aluminum bar bell, improved racing oil pickup brace, and ICT Billet oil cooler block off. Little upgrades. I’m deleting the oil cooler/heater thing. Mostly because this engine had lots of metal in the pan and I don’t trust that the cooler brick thing is going to clean up. Simpler is better. They made millions of 5.3 suburban and trucks without them so it’s not gonna make a difference for near-stock performance. I’ll just run some rotella t4 in it. That stuff is really good for summer time.
IMG_9448.jpeg
IMG_9448.jpeg (3.16 MiB) Viewed 369 times
We’re gettin it. Slowly but surely.

Gotta torque the cam bolt down and throw the front cover on but it’s basically all together.

Will continue this next week.
User avatar
Mooseman
Posts: 1075
Joined: Mon Jun 12, 2017 11:35 pm
Location: Ottawa, ON Canada
Contact:

Re: Pit Maneuver Survivor

Post by Mooseman »

I like the retro orange look. Good work.
2011 Caprice PPV, former RCMP test vehicle, never put into service
Build Thread: http://www.newcaprice.com/forum/viewtopic.php?t=2419
User avatar
rustingsoftly
Posts: 19
Joined: Sun Jan 07, 2024 11:50 pm

Re: Pit Maneuver Survivor

Post by rustingsoftly »

Mooseman wrote: Fri Feb 09, 2024 6:04 pm I like the retro orange look. Good work.
Thanks. We’re given it a whirl.
User avatar
rustingsoftly
Posts: 19
Joined: Sun Jan 07, 2024 11:50 pm

Re: Pit Maneuver Survivor

Post by rustingsoftly »

Engine is sitting in there. I’ll try to get the starter and wiring harness ironed out tomorrow. Getting closer. Have a coolant hose, filters, and suspension part on order. Should get it fired up this week hopefully. Running and driving next week??? Fingers crossed! Needs alignment really bad. Car never was aligned after they dropped the cradle to swap motors and it has bad right front/lower rear control arm. Everything else suspension related felt great.
Attachments
IMG_9741.jpeg
IMG_9741.jpeg (3.74 MiB) Viewed 210 times
Scrammbledeggs
Posts: 51
Joined: Wed Jul 26, 2023 10:20 pm

Re: Pit Maneuver Survivor

Post by Scrammbledeggs »

Hell yes keep it up !
Post Reply