<sarcasm> It's nice the government didn't over react. </sarcasm>Mooseman wrote: ↑Fri Oct 08, 2021 9:58 am It came with the lights and all? Man, that would be illegal here, especially after what happened here in Nova Scotia https://en.wikipedia.org/wiki/2020_Nova_Scotia_attacks. In fact, the RCMP has stopped selling their old PCs to the public even if they are stripped.
2013 PPV Weekend Warrior/Mad Max Build
Forum rules
One thread per car per member in this section. No thread hijacking in this section please, if it's strictly a tech discussion please move it to the appropriate sub-forum - moderators can assist if needed or requested.
One thread per car per member in this section. No thread hijacking in this section please, if it's strictly a tech discussion please move it to the appropriate sub-forum - moderators can assist if needed or requested.
-
- Posts: 2301
- Joined: Sat Feb 07, 2015 2:31 pm
- Location: Pearland, Texas
Re: 2013 PPV Weekend Warrior/Mad Max Build
Gene Beaird,
Pearland, Texas
2012 Caprice 9C1
1992 B4C 1LE Camaro
2018 Tahoe PPV (her car)
1995 DGGM Impala SS
1985 Firebird - 310 LS1 C Prepared autocross car.
1980 Bluebird Wanderlodge
And some others
Do YOU have my SPID?
Pearland, Texas
2012 Caprice 9C1
1992 B4C 1LE Camaro
2018 Tahoe PPV (her car)
1995 DGGM Impala SS
1985 Firebird - 310 LS1 C Prepared autocross car.
1980 Bluebird Wanderlodge
And some others
Do YOU have my SPID?
Re: 2013 PPV Weekend Warrior/Mad Max Build
V6 (silver one) is now daily driver for my son.
It really runs well, the V6 is no slouch at 300 hp. Rides like a Caddy
Had mine to the track - went 11.77, but differential axle seal let go only letting me make one pass.
(LOTS of smoke - rear end grease directly on hot exhaust)
It really runs well, the V6 is no slouch at 300 hp. Rides like a Caddy
Had mine to the track - went 11.77, but differential axle seal let go only letting me make one pass.
(LOTS of smoke - rear end grease directly on hot exhaust)
Re: 2013 PPV Weekend Warrior/Mad Max Build
Noice! 1 A video from the track would be cool too! Here's an easy way to share it here, if you have a Google account (Gmail, YouTube, etc). https://support.google.com/drive/answer ... %3DDesktop
Re: 2013 PPV Weekend Warrior/Mad Max Build
Hey Barry, what was the width on the rims you widened? I acquired a set of 20X11 with 315/35/20's for the rear and 20X9 275/40/20's for the front from a Zl-1 track racer. Was planning on using on a different project and they are just to big. I ran the tire calculator for yours and mine and came up with this:
315/35/20 28.7" H, 12.4" W
325/45/20 29.5 H, 12.8" W
You stated that your tires are 30.2"
I assume that my wheels and tires will fit if the offset is correct?
What do you think?
Thanks
Mike
315/35/20 28.7" H, 12.4" W
325/45/20 29.5 H, 12.8" W
You stated that your tires are 30.2"
I assume that my wheels and tires will fit if the offset is correct?
What do you think?
Thanks
Mike
-
- Posts: 38
- Joined: Fri May 28, 2021 2:47 pm
Re: 2013 PPV Weekend Warrior/Mad Max Build
I have a pretty similar setup. 10” widened oem rims on 315/45. Did you do anything to dealBarryM wrote: ↑Sat Nov 13, 2021 8:00 am V6 (silver one) is now daily driver for my son.
It really runs well, the V6 is no slouch at 300 hp. Rides like a Caddy
Had mine to the track - went 11.77, but differential axle seal let go only letting me make one pass.
(LOTS of smoke - rear end grease directly on hot exhaust)
13 and 14.jpg
With the ABS not working due to the tire diameter mismatch front to rear? The warnings are pretty annoying. I couldn’t find anything programmable in the ABS module to allow a different size front to rear.
2013 PPV Phantom black 1,077 RWHP 1,015 RWTQ 9.9@148
LS3 stroker 417ci, Callies crank w/ Malhe pistons & Darton sleeves. 11.5:1
Procharger F1a94. 22 psi boost E85
Water/Meth + 180hp N20
BTR custom cam 235/257 .638/.629 116, BTR shaft rockers Johnson 2126 lifters
BTR Trinity intake Kooks headers w/ Solo exhaust 3"
CDT Level 4 trans build w triple disc TC
Holley 120lb injectors
MT ET Street R 305/45/R18 on 10" widened OEM wheels.
LS3 stroker 417ci, Callies crank w/ Malhe pistons & Darton sleeves. 11.5:1
Procharger F1a94. 22 psi boost E85
Water/Meth + 180hp N20
BTR custom cam 235/257 .638/.629 116, BTR shaft rockers Johnson 2126 lifters
BTR Trinity intake Kooks headers w/ Solo exhaust 3"
CDT Level 4 trans build w triple disc TC
Holley 120lb injectors
MT ET Street R 305/45/R18 on 10" widened OEM wheels.
Re: 2013 PPV Weekend Warrior/Mad Max Build
No I have not - Shortly after pulling out the garage it throws a couple fits about ABS then disables.
Congrats on a great build in your signature - you will have a lot of fun with that ride !
Congrats on a great build in your signature - you will have a lot of fun with that ride !